CCNA201~250題

( ) 201.Which mode can you set the multiple virtual interfaces on a physical interfaces?

               A.line

               B.interface

               C.privilege

               D.User

               E.subinterface

( ) 202.Which one of following commands is used to display a list of commands?

               A.Taipei#?cl?

               B.Taipei#cl?

               C.Taipe#cl?

               D.Taipei#?cl

               E.Taipei#c?l?

( ) 203.Which commands will you use to load configuration file from NVRAM to RAM?

               A.Taipei#copy startup-config running-config

               B.Taipei#copy NVRAM RAM

               C.Taipei[config]#copy startup-config running-config

               D.Taipei[config]#copy NVRAM RAM

( ) 204.Which of the following command will you use to display the name of the IOS image file being used in a Cisco router?(choose 2)

               A.Router#show interface

               B.Router#show flash

               C.Router#show image

               D.Router#show version

               E.Router#show IOS

( ) 205.You have a new router and wish to have the router prompt you through the initial configuration commands. What router mode do you use?

               A.ROM Monitor mode

               B.Auto mode

               C.SETUP mode

               D.User mode

( ) 206.You set the configuration Register to 0x0, what will be result?

               A.Boot from Rom

               B.Boot from flash

               C.Boot from Network

               D.Enter the Rom monitor mode

               E.Boot from NVRAM

( ) 207.You are using IOS 10.3 earlier,which command will you use to execute the command in NVRAM?

               A.Taipei#config IOS

               B.Taipei#config NVRAM

               C.Taipei#config network

               D.Taipei#config memory

( ) 208.Which IOS command will you use to open the history buffer and displays the most recently entered commands?

               A.Show commands

               B.Show buffers

               C.Show history

               D.Show terminal buffer

               E.Show memory

( ) 209.Which command will you use to load a configuration file from a TFTP Server to RAM?

               A.Taipei#copy tftp config

               B.Taipei#copy tftp running-config

               C.Taipei#copy tftp startup-config

               D.Taipei#copy tftp RAM

( ) 210.Which command will you use to set the encrypted password to protect access to the privileged mode?

               A.set passward

               B.set secret

               C.enable secret

               D.set enable secret

( ) 211.You have a new router and want to upgrade the IOS. The new IOS image is located on a TFTP server. What command will you to download the new IOS version?

               A.Router#copy flash tftp

               B.Router#copy tftp flash

               C.Router(config)#copy flash tftp

               D.Router(config)#copy tftp flash

               E.Router#copy flash run

( ) 212.Which one of following commands will you use to backup system image file to a network server?

               A.Taipei#copy flash tftp

               B.Taipei#copy IOS tftp

               C.Taipei#copy running-config tftp

               D.Taipei#copy startup-config tftp

( ) 213.Which one of following commands are you in the controller configuration mode?

               A.Taipei[config]#

               B.Taipei#

               C.Taipei [controller-config]

               D.Taipei[config-controller]

               E.Taipei[config-if]

( ) 214.Which one of following commands will you use to show the backup configuration file?

               A.show flash

               B.show tftp

               C.show running-config

               D.show startup-config

( ) 215.You use the command "copy flash tftp",which three information do you need to enter?

               A.The name of source system image file

               B.The name of destination system image file

               C.The name of the Router

               D.IP address of the local host

               E.IP address of the remote host

( ) 216.What kind of information can you get form an IOS image file name(choose three answers)

               A.Running location

               B.Feature capability

               C.Hardware platform

               D.Memory

               E.CPU used
               F.Hardware channels

( ) 217.Which two of followings can you configure within the setup dialog?

               A.local

               B.Global

               C.interface

               D.clock rate

( ) 218.Which command will you use to display the total router memory and available memory?

               A.show running-config

               B.show startup-config

               C.show flash

               D.show memory

( ) 219.Which command will you use to save the configuration to NVRAM?

               A.Taipei#copy running-config startup-config

               B.Taipei#save running-config startup-config

               C.Taipei[config]#copy running-config startup-config

               D.Taipei[config]#save running-config startup-config

( ) 220.Which one of the command will you use to display active processes?

               A.show version

               B.show memory

               C.show processes

               D.show active processes

( ) 221.Which command will you use to set the message "Test"for an interface?

               A.Taipei#description Test

               B.Taipei[config]#description Test

               C.Taipei[config-if]#description Test

               D.Taipei[config-sub-if]#description Test

( ) 222.How many command lines are stored in router's history buffer by default?

               A.1

               B.10

               C.50

               D.100

               E.200

( ) 223.Which command will you use display the amount of memory that is being used by the current IOS image and whether there is enough room available to upgrade the new IOS images of a router?

               A.Router#show interface

               B.Router#show memory

               C.Router#show flash

               D.Router#show buffer

               E.Router#show version

( ) 224.You use two routers to connect directly together using serial interfaces in a back-to-back configuration. What additional command is needed to bring this link up?

               A.no shut down

               B.clockrate

               C.clock rate

               D.DEC rate

               E.DTE rate

( ) 225.You want to see the banner to display HELLO,which command will you use?

               A.Taipei#banner#HELLO#

               B.Taipei[config]#banner#HELLO&

               C.Taipei>banner motd &HELLO&

               D.Taipei[config]>#banner motd # HELLO #

( ) 226.You are an administrator at Magic Corporation.You have forgotten the password to one of your routers.After completing the password recovery procedure the router returned to its normal operation. The config-register was set back to the initial default value. What is this value?

               A.0x2112

               B.0x2104

               C.0x2102

               D.0x2142

               E.0x2100

( ) 227.After configuring a Cisco router. You save the changes on the startup configure and reboot the router.You found none of your changes are active and the router boots to the initial configuration mode.Which of the following best describe problem?

               A.Startup-config in NVRAM failed

               B.Hardware failure prevents the router from loading the configuration.

               C.Startup-config in flash failed

               D.The configuration-register was set to bypass startup configuration

               E.The configuration-register was set to load startup configuration,but failed

( ) 228.Which command will you use to set the EXEC timeout 30 minutes?

               A.exec-timeout 30 0

               B.exec-timeout 1800

               C.timeout 30 0

               D.timeout 1800

               E.enable timeout 30

( ) 229.Which router mode will you use when you want to backup image file to network server?

               A.Global

               B.local

               C.line

               D.Privilege

               E.interface

( ) 230.You finish the setup dialog and answer yes to use the configuration ,what will router do?(choose 2)

               A.Load the configuration to RAM

               B.Save the configuration to NVRAM

               C.Boot from RAM

               D.Boot from NVRAM

( ) 231.Which one of following is in global configuration mode?

               A.Taipei>

               B.Taipei#

               C.Taipei[global]

               D.Taipei[config]

               E.Taipei[config-global]

( ) 232.Which one of following is in user mode?

               A.Taipei>

               B.Taipei#

               C.Taipei[config]

               D.Taipei[config-if]

( ) 233.Which one of following is in privilege mode?

               A.Taipei>

               B.Taipei#

               C.Taipei[config]

               D.Taipei[con-fig-if]

( ) 234.A router can't find the image file specified in the Register,what will the routed do?

               A.Boot from RAM

               B.Boot from NVRAM

               C.Enter the ROM Monitor mode

               D.Enter the setup mode

( ) 235.How many user can access a Routes' configuration at the same time?

               A.1

               B.3

               C.5

               D.7

               E.9

( ) 236.Which one of following are you used in interface configuration mode?

               A.Taipei#

               B.Taipei[if]#

               C.Taipei[config-if]

               D.Taipei[interface]

               E.Taipei[interface-if]

( ) 237.Which one of following are you in the subinterface configuration mode?

               A.Taipei#

               B.Taipei[config]#

               C.Taipei[config-if]

               D.Taipei[config-subif]

( ) 238.Which router mode can you use to set a router by answering a series questions?

               A.setup

               B.Local

               C.Global

               D.line

               E.interface

( ) 239.You want to set a password to get into the privileged mode, which command will you use?

               A.set password

               B.enable password

               C.set enable password

               D.enable set password

               E.enable secret

( ) 240.You mode some change on your Router.What sequences occur after your router is powered up?

               A.Perform POST,load the Cisco IOS software,locate Cisco IOS software, apply configuration statements

               B.Locate Cisco IOS software,load the Cisco IOS software,apply configuration statements,locate configuration statements,and perform POST

               C.POST,locate Cisco IOS software,load the Cisco IOS software,locate configuration statements,and apply configuration statements.

               D.POST, Test software routines,load configuration files,load the Cisco IOS software,test Cisco IOS software

( ) 241.You want a router to boot a file name test.exe from a network IP address 200.20.20.20,which command will you use?

               A.Taipei#boot network test.exe 200.20.20.20

               B.Taipei[config]#boot tftp test.exe 200.20.20.20

               C.Taipei#boot system tftp test.exe 200.20.20.20

               D.Taipei[config]#boot system tftp test.exe 200.20.20.20

               E.Taipei[config-if]#boot system tftp test.exe 200.20.20.20

( ) 242.Which command will you use to display a router's command history?

               A.Show running-config

               B.Show history

               C.display history

               D.display command

               E.view command

( ) 243.Which command will you use to enter the setup mode?

               A.Taipei#setup

               B.Taipei[config]#router setup

               C.Taipei#enable setup

               D.Taipei[config]#enter setup

               E.Taipei#enable router setup

( ) 244.Which command will you use to display all configured protocols?

               A.show version

               B.show protocols

               C.show interfaces

               D.show interfaces protocols

( ) 245.Why do you use the enable secret command instead of the enable password command? 

               A.more memory

               B.more bandwidth

               C.It's faster

               D.It's a better encryption algorithm

               E.It has more function

( ) 246.Which one of startup sequence is the default setting of a router?

               A.RAM , NVRAM , Flash , TFTP Server

               B.NVRAM , TFTP Server , Flash , ROM

               C.TFTP Server , NVRAM , Flash , ROM

               D.NVRAM , TFTP Server , Flash , RAM

               E.NVRAM , Flash , TFTP Server , ROM

( ) 247.Which command will you use to display active configuration?

               A.show version

               B.show running-config

               C.show startup-config

               D.show active config

               E.display active

( ) 248.Which of following commands will you use to enable others to establish a Telnet session on a Cisco router?

               A.Taichung(config)#line vty 0
                   Taichung(config-line)#password test
                   Taichung(config-line)#login

               B.Taichung(config)#line console 0
                   Taichung(config-if)#enable password test

               C.Taichung(config)#line vty 0 4
                   Taichung(config-line)#enable password test

               D.Taichung(config)#line vty 0 4
                   Taichung(config-line)#enable secret test
                   Taichung(config-line)#login

               E.Taichung(config)#line console 0
                   Taichung(config-line)#password testk

                   Taichung(config-line)#login

( ) 249.Which command will you use to enter the global configuration mode?

               A.Taipei#config global

               B.Taipei#config interface

               C.Taipei#config setup

               D.Taipei#config terminal

( ) 250.Which command will you use to name a router Taipei?

               A.Taipei>name Taipei

               B.Taipei#name Taipei

               C.Taipei#host name Taipei

               D.Taipei[config]#hostname Taipei